Ross ADC-9032 Uživatelský manuál

ADC-9032Analog Composite to SDI Video ConverterUser Manual

9 • Installation (Iss. 05)adhesive is very aggressive and is not easily removed. The adhesive will cure fully in 24 hours.To install Surface Mount St

Installation (Iss. 05) • 10 To install the Flat Metal Plate1. Affix the flat metal plate to the bottom of the chassis using the chassis screws as show

11 • Installation (Iss. 05)Figure 4 BMP-9000 Mounting Bracket

Setup (Iss. 05) • 12 SetupPower Adaptor and SupplyConnect the PS-9000 power adaptor to the power supply connector. The PS-9000 provides regulated +5V

13 • Setup (Iss. 05)Status and Selection LEDsThe front panel of the module has four LEDs that display the status of the input signals, and indicate m

Setup (Iss. 05) • 14 b.For menu items that have multiple selections, the LED will be in a state as indicated in the FunctionSetup and Configuration Me

15 • Configuration (Iss. 05)ConfigurationUse the Function Select switch and the Down and Up buttons to configure the ADC-9032 to convert analog video

Configuration (Iss. 05) • 16 2. To change Video Standard configuration to PAL (625/50):• Keep the Function Select in Position 0.• Press the Down butto

17 • Configuration (Iss. 05)4Video LevelMax. Level +(h)Level between Unity and Max.+(h)Unity*Level between Min. and Unity–(h)Min. Level –(h)5

Configuration (Iss. 05) • 18 Function Menu NotesSome of the menu items in Table 2 are explained here in further detail as follows:Video StandardUse th

1ADC-9032 User Manual• Ross Part Number: 9032DR-004-05• Release Date: October 11, 2012.The information contained in this manual is subject to change

19 • Configuration (Iss. 05)Auto GainUse this menu to automatically try to compensate for any perceived gain deficiencies. Auto Gain is based on sync

Configuration (Iss. 05) • 20 Setup OnIf the incoming analog composite video has Setup, then this user-controlled setting should be set to On. If there

21 • Configuration (Iss. 05)Status ReportThis menu selection is primarily for Ross Video use.If an on-board error has occurred with the ADC-9032, thi

Configuration (Iss. 05) • 22 Table 3 ADC-9032 Menu Access by Video Standard SelectionSwitch Position and Menu ItemAnalog Video StandardsNTSC, PAL-M P

23 • Technical Specifications (Iss. 05)Technical SpecificationsNote that specifications are subject to change without notice.Table 4 ADC-9032 Techni

Technical Specifications (Iss. 05) • 24 PerformanceLine Rate Tilt <0.5%Field Rate Tilt <0.5%Differential Phase <1°Differential Gain <1.5%P

25 • Service Information (Iss. 05)Service InformationWarranty and Repair PolicyThe ADC-9032 is warranted to be free of any defect with respect to per

Service Information (Iss. 05) • 26 Notes:

Contact UsContact our friendly and professional support representatives for the following:• Name and address of your local dealer• Product information

2 Important Regulatory and Safety Notices to Service PersonnelBefore using this product and any associated equipment, refer to the “Important Safety

3Important Safety Instructions1. Warning – Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. The

4 EMC NoticesUnited States of AmericaFCC Part 15This equipment has been tested and found to comply with the limits for a class A Digital device, purs

5“Contact Us” section on the last page of this manual. All GearLite products are covered by a generous 3-year warranty and will be repaired without c

Introduction (Iss. 05) • 6 IntroductionOverviewThe ADC-9032 Analog Composite to SDI Video Converter is a high-quality signal conversion solution withi

7 • Introduction (Iss. 05)FeaturesThe ADC-9032 has the following features:• Supports NTSC, PAL-B, PAL-M, PAL-N (combinational) composite analog video

Installation (Iss. 05) • 8 InstallationStatic DischargeWhenever handling the ADC-9032 and other related equipment, please observe all static discharge